![]() You have to reinstall the radio, close the reverse light compartment, and tighten every screw and bolt, back into its place. It is now time to put everything back in its place. You can either connect to the same power source as your car radio, or get power through the vehicle’s fuse box. In a situation where you are using a wireless backup camera system, you will additionally have to provide power for the receiver. If your vehicle uses a CAN Bus decoder to control its reverse lights, then there will be no need for a trigger cable.Ĭ). Wireless systems usually have a trigger wire on this receiver end. If your monitor supports trigger wires, then connect the trigger wire to your monitor. If you have a wireless system, then connect the single yellow plug from the receiver to your car radio.ī). Connect the other yellow, RCA male plug from the long cable, to your car radio’s video input. If your backup camera system, is the wireless type with a transmitter and receiver, then you can skip this step. ![]() You will now have to run the cable from your car’s rear, to the front. The receiver part of wireless setups, usually have just one yellow plug, and a trigger wire. This is the transmitter part of a wireless system. If your camera is a wireless system, then you will have to connect the cable with the red and yellow plugs to the camera. Please note that your monitor will have to support trigger cables, for this to work.Į). If you want the monitor to automatically show the camera’s feed once you change into reverse gear, then connect this trigger wire to the same +12V cable of your reverse light. This same long cable, should have a short wire branching out from each RCA plug. Connect one of these plugs, to the yellow, RCA female plug from the camera.ĭ). There will be a long cable with a yellow, RCA male plug on each end. The red wire connects to the +12V reverse cable, while the black one connects to either the -12V, or the vehicle’s chassis (ground).Ĭ). Connect the other 2 ends of this power cable to your vehicle’s reverse light. One wire is usually red, and the other, black.ī). Connect the DC power cable to the red DC female plug of the camera. This is where it gets a little complicated for many people, so pay attention.Ī). Most cameras will come with an installation kit, so use it and install the camera properly. ![]() License plate cameras for cars, and roof-top cameras for vans, are the easiest to install. This can be easy or difficult, depending on the type of camera you have. The second step is the installation of the backup camera. Your vehicle’s manual will come in handy here, because it can offer useful diagrams, which can help you to properly unmount the necessary parts of the car. You will also have to make way in your car’s rear, to find cables that power the reverse light, and to optimally install the camera itself. The first step is the careful removal of your vehicle’s dashboard, or any other part that needs to be removed, before the installation can continue. The 7-Step Backup Camera Installation Process Step 1: Take The Car Apart Having the right tools enables you, to carefully and cleanly remove parts of the vehicle, which are necessary for a successful installation. You will need screwdrivers, pliers, pin and trim removal tools, depending on your type of vehicle. Check to confirm if your vehicle controls your brake light, using a CAN Bus, because if it does, then you don’t need to install a trigger cable. Whenever available, the monitor uses the trigger cable to know when to switch to the camera’s feed. Trigger cables are single wires that run from a video monitor to the reverse light of a car. The Controller Area Network, also referred to as CAN Bus, is a system used by car makers to make wiring easier in a vehicle. In such a case, you will have to get an adapter. You can check your vehicle’s manual for clarification.Īlthough the video input would mostly be a yellow-colored female RCA plug, some car makers can also have unique plugs for their system’s video input. This is the first step, because if your head-unit can’t handle video, then there is no need to continue. They are as follows: – Confirm Your Radio’s Video Input In order to guarantee your success with this install, there are a few prerequisites that you must have to attend to, before moving on. There could be other conditions for installing the camera, but this guide assumes that your vehicle already has a monitor installed. And if you would love to install a camera, or to just upgrade an existing one, then this guide is for you. If your vehicle lacks a backup camera, but has a radio with a video monitor.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |